Search found 98 matches
- Fri May 29, 2015 9:54 pm
- Forum: Windsurfing Discussion
- Topic: Tri-fin Conversion
- Replies: 70
- Views: 23141
Sorry to hear the grub screws failed on you. That is disappointing. Udder only used his once for a short time, so not sufficient testing in that case. WSF has used his a fair bit and not reported any problem to date, but time will tell with regard to his. If they are to be considered suitable they s...
- Wed Apr 22, 2015 1:07 pm
- Forum: Windsurfing Discussion
- Topic: New wide boards: Gecko, Firemove etc
- Replies: 51
- Views: 15931
I have the firemove 110 ltr. Dido KC7777 results. I have slimmed down from my 235lbs to 210 lbs but at both weights it was very stable for me, only now I think I could uphaul it if i had to. I am running a much smaller fin (24cm) than what it comes with stock, even with my 6.0, just the 24cm. Trucks...
- Wed Apr 22, 2015 5:11 am
- Forum: Windsurfing Discussion
- Topic: Tri-fin Conversion
- Replies: 70
- Views: 23141
- Tue Apr 21, 2015 1:18 pm
- Forum: Windsurfing Discussion
- Topic: Tri-fin Conversion
- Replies: 70
- Views: 23141
- Fri Mar 20, 2015 10:28 pm
- Forum: Windsurfing Discussion
- Topic: Tri-fin Conversion
- Replies: 70
- Views: 23141
- Mon Mar 16, 2015 11:26 am
- Forum: The Rigging Area
- Topic: 1111 - or why did I log my sailing sessions?
- Replies: 18
- Views: 9109
- Thu Mar 12, 2015 5:48 pm
- Forum: Windsurfing Discussion
- Topic: Deck Delam. Rebuild http://1drv.ms/1Mv5bNM
- Replies: 12
- Views: 3986
- Thu Mar 12, 2015 4:35 pm
- Forum: Windsurfing Discussion
- Topic: Deck Delam. Rebuild http://1drv.ms/1Mv5bNM
- Replies: 12
- Views: 3986
- Thu Mar 12, 2015 4:00 pm
- Forum: Windsurfing Discussion
- Topic: Deck Delam. Rebuild http://1drv.ms/1Mv5bNM
- Replies: 12
- Views: 3986
Lots of taper sanding!!! No but joints!!! Also, I do cut it on a taper to start with to reduce the amount of sanding. Only carbon in the rails of that JP board. Haven't worked on a full carbon board yet. Only divinycell and divinycell/wood. Good point. Guess your mini sup was carbon. I suppose the c...
- Thu Mar 12, 2015 1:17 pm
- Forum: Windsurfing Discussion
- Topic: Deck Delam. Rebuild http://1drv.ms/1Mv5bNM
- Replies: 12
- Views: 3986
What have you been wearing for protection while working on the board? I freaked myself out last month when I was sanding carbon and then after reading about what can happen if it gets into your blood stream. Just the cheap 3M dust masks with the wire nose seal. Fortunately next to no sanding requir...
- Thu Mar 12, 2015 1:06 pm
- Forum: Windsurfing Discussion
- Topic: Deck Delam. Rebuild http://1drv.ms/1Mv5bNM
- Replies: 12
- Views: 3986
nice work, looks really good. i like how you ditched the unnecessary inserts, very pro. so is it just me or do you see a disproportionate number of JP boards when you are looking up deck delam and repair? :D :evil: Well I haven't personally seen them, but most of the deck repairs on websites seem t...
- Thu Mar 12, 2015 11:25 am
- Forum: Windsurfing Discussion
- Topic: Deck Delam. Rebuild http://1drv.ms/1Mv5bNM
- Replies: 12
- Views: 3986
Deck Delam. Rebuild http://1drv.ms/1Mv5bNM
Pictures Here http://1drv.ms/1Mv5bNM This board had a major deck delam. between the divinycell and the eps. My theory is that it was caused by a manufacturing defect allowing copious amounts of water to enter the board in fairly large amounts. (may have been just hard sailing, but I like my theory :...
- Tue Mar 10, 2015 8:09 pm
- Forum: Windsurfing Discussion
- Topic: Tri-fin Conversion
- Replies: 70
- Views: 23141
The toe-in K4 measured on production boards is very small and in some cases 0 or nearly undetectable. K4 say that they feel toe-in is very important and will gladly sell fins with toe-in built into the fin (1, 2 or 2.8 deg). This is to enable someone with a production board to get toe-in if they fee...
- Mon Mar 09, 2015 12:55 pm
- Forum: Windsurfing Discussion
- Topic: Tri-fin Conversion
- Replies: 70
- Views: 23141
- Sun Mar 08, 2015 10:03 pm
- Forum: Windsurfing Discussion
- Topic: Tri-fin Conversion
- Replies: 70
- Views: 23141
IMHO it's not the boxes that will be problematic, they'll hold the lateral loads fine, it's the fins. Standard FCS fins made for a surfboard don't have the right shape and are too flimsy for a windsurf board powered and planing. But if you can buy windsurf fins with FCS tabs then you're set. Nanmoo...